Question:

I have to read a Citroen C3 1.2 Petrol ECU V56.12 but the wiring connection in Xhorse Multi Prog Boot Mode is missing.

Solution:

Multi Prog does PSA Valeo V56.x in boot mode only.

Here is the boot mode pinout.

 Problem:

It is a 2008 VW Toureg with Kessy module. Weld up and read back-up data with xhorse vvdi key tool plus successfully. But it fails to read immo data. Tried several times. Welding is good.
What could be the problem?

Solution:

Don’t have to read immo data from the Programmer menu.

Go through the IMMO menu and loaded the “backup data” you read with the programmer, and it will give the the pin and 7 byte cs code.

Go to this screen and load the data you’ve read.

Same system as 2008 Porsche Cayenne.

 Question:

Will Xhorse VVDI Key Tool Max Pro Add a Key to my Peugeot Boxer 2.2 2009 with magneti marelli immo?

Yes, key tool max pro will add a spare key to Peugeot Citroen ID48 with Marelli IMMO system.

Go to IMMO system (Marelli 70F3238 + 95320 ID48) function.

Supports read eeprom, write eeprom, make dealer key, key programming, adapt remote key and renew remote.

If need to add a new key, follow steps below to finish key programming.

FYI:

If your car has id46 transponder then no problem for you, can use precoded transponder and program in car via diagnostic device but if is immo3 with id48 than you need special precoded id48 chip from vin from dealer or need make transponder with key maker from dump and need rewrite new dump which will be produce during transponder programing. in this mean the transponder is ready to start car.

www.vvdishop.com

 Here comes the solution to Xhorse Condor XC-Mini Plus II error code 6. Hope it helps if the same error occurs.

Solution:

When decoding or cutting keys by Condor  2, Error Code 6 indicates abnormal conductivity in the probe or cutter.

Follow the step-by-step guide below to solve it.

Step 1: Conductivity Test

Perform a conductivity measurement to diagnose the problem:

1.Navigate to Settings > Machine Test > Electrical Conductivity Measurement.

2.Follow the on-screen prompts to connect either the probe or cutter (not both).

3.Start the test.

Step 2: Test Results

If both the probe and cutter light up green simultaneously:

This indicates a short circuit between the probe and cutter.

Step 3: Inspect for Iron Filings

Check for iron filings around the three screws above the probe.

Clean the area thoroughly to remove all debris.

Step 4: Reinstall Screws

If the problem persists, remove the three screws above the probe.

Clean the area around the hole to ensure no iron filings remain.

Reinstall the screws, but:

Do not overtighten, as this can damage the insulation plastic ring on the screws, causing a short circuit.

Step 5: Check Conductive Wires

Restart the test. If the probe green light turns on before connecting:

• Indicates the probe is in a short circuit state.

Inspect the conductive wires on the probe disk for damage.

• Damaged wires should be wrapped with insulating tape.

Conclusion:

Retest conductivity using the Xhorse Condor XC Mini Plus II Key Cutting Machine’s test interface.

If the issue persists, consider replacing faulty components or contacting the manufacturer.

www.vvdishop.com

 Problem:

Generate remote successfully with vvdi mini key tool but it says Storage space of reward points will soon be full.

Solution:

If you are using the old VVDI Key Tool (black one), run Xhorse upgrade kit, hit Find device then Upload bonus point.

If use other key tools (Mini key tool, key tool lite, key tool max, key tool plus), in Home menu, collect points and sync.

 Xhorse Multi Prog is possible to change the odometer for VAG MQB 5A cluster. You can read it for immo.

Besides being able to make lost keys (Read micro v850 and rh8505a), Odometer also works.

Example:

Mileage change rh850 5a
With multiprog.
Everything ok.

Original mileage 52,216 km

Desired mileage: 890km

 If your Xhorse VVDI Key Tool Max pro fails to start communication with vehicle and asks to check if the OBD wiring is normal, follow guide below to do a device self test.

VVDI Key Tool Max Pro Self Test

In main menu select IMMO Programming

Select More Functions

Press Device Test

Select K-line Test

Short Connect PIN7 and PIN15 with the OBD connector.

If Key Tool Max Pro says the test failed, there is something wrong with the device. You may need to send it back for repair.

https://www.vvdishop.com/service/vvdi-key-tool-max-pro-self-test.html