Here obdii365.com lists all table comparisons of Autel Maxidiag MD808 Pro and similar competitive diagnostic scan tools, including, MD802, Autolink, CRP129 and MX808 etc.




Comparison Table 1:
Autel MaxiDiag MD808 Pro full vs. Maxidiag MD802 Elite Full vs. MD808 four system vs. MD802 four system
https://eobd21.files.wordpress.com/2018/07/autel-md802-vs-md808-pro.jpg?w=125 125w, https://eobd21.files.wordpress.com/2018/07/autel-md802-vs-md808-pro.jpg?w=250 250w" sizes="(max-width: 600px) 100vw, 600px" />
What the advantages of MD808 Pro compare with MD808 basic and MD802?

1.MD808 PRO support all system of car, the md808 only support 4 system , and MD808 PRO is upgrade version of MD808 and MD802 , coverage more car and more systems.
2.MD808 PRO support Steering Angel Learning , DPF functions , and Battery Registration and reset .
The MD808 4 system and MD802 don’t have these functions.
3. Autel MD808 pro is not just a diagnostic tool, but a professional service tool to service individual specialized systems, including Oil Reset, EPB, SAS, BMS and DPF, offers quick and easy solution to everyday task in the workshop;
Based on the ARM Thumb Processor (400 MHz), it needs only 6s booting time to allow you to build a more fluid user experience.
4. For MD808 PRO, Live data graphing for all available modules.
5. Brand New Design: Autel MD808 pro, a revelation in diagnostic and service tool is launched with brand–new exterior in terms of design, structure and buttons;
6. Efficient Diagnosis: MD808 PRO Offer more advanced features and functions to troubleshoot basic four systems (Engine, Transmission, SRS and ABS) for major vehicles on the road today;
7. Powerful Hardware: MD808 PRO Included with 16G Micro SD Card, full color 800*480 display to take your diagnostic experience to a whole new level.




Comparison Table 2:
Autel MaxiDiag MD808 Pro vs. Launch CRP129
https://eobd21.files.wordpress.com/2018/07/autel-md808-pro-vs-crp129.jpg?w=150 150w, https://eobd21.files.wordpress.com/2018/07/autel-md808-pro-vs-crp129.jpg?w=300 300w" sizes="(max-width: 600px) 100vw, 600px" />
Comparison Table 3:

MD808 Pro vs. Autolink 609P vs. Autolink AL629
https://eobd21.files.wordpress.com/2018/07/autel-md808-vs-al629.jpg?w=137 137w, https://eobd21.files.wordpress.com/2018/07/autel-md808-vs-al629.jpg?w=274 274w" sizes="(max-width: 600px) 100vw, 600px" />
Comparison Table 4:
Autel Maxidiag MD808 vs. MaxiCheck MX808

www.obdii365.com

Here are tips and guides of cloned VAS5054A software ODIS Service 4.3.3 Error ODS9004E.

Error message:

odis 4.3.3 error ods9004e

Infrastructure VW online connection. Mirror server 2: cannot connect to mirror server 2.

https://eobd21.files.wordpress.com/2018/07/odis-4-3-3-ods9004e-error.jpg?w=150 150w, https://eobd21.files.wordpress.com/2018/07/odis-4-3-3-ods9004e-error.jpg?w=300 300w" sizes="(max-width: 470px) 100vw, 470px" />

Solutions: (credits to kmaverick and sunaj )

Run program as ADMIN!

You DON’T need a username and password… but you must point the program to a valid and correct path to your locally stored database.

https://eobd21.files.wordpress.com/2018/07/odis-4-3-3-path.jpg?w=150 150w, https://eobd21.files.wordpress.com/2018/07/odis-4-3-3-path.jpg?w=298 298w" sizes="(max-width: 504px) 100vw, 504px" />

Check in Program Files\ODIS Service xyz\log for ENGINE.LOG

Might Program Files x86, use brain to locate file

Check if green file exists….

An exception occurred while downloading feature from “file:/C:/ODIS%20DATA/ODIS-Service_update_4_3_3-EU_20180626_YGHLY/Odis/Trade-Retail/software/update/features/odis.main.service_51.0.10.jar”

Your path could be too long, so change to short path like C:\PostSetup\ODIS\Trade-Retail with correct folder structure!

Then try a copy of these two main files odis.main.service_51.0.10.jar and 51.0.20:

https://we.tl/UGvbvbEJkZ

And also install 540 fine and 550 is only a small update mainly Bentley

Seems the local copy of odis.main.service_51.0.10.jar was good, now it upacks ok

With ODIS, if you do a clean install then get errors like pp had with 550 and missing file(s) but now you have a database loaded, update to 550 with no problems now… go figure!

ODIS is working finally

https://eobd21.files.wordpress.com/2018/07/odis-4-3-3-install.jpg?w=150 150w, https://eobd21.files.wordpress.com/2018/07/odis-4-3-3-install.jpg?w=300 300w" sizes="(max-width: 508px) 100vw, 508px" />

Tip & Guides:

ODIS-S 4.3.3 source: 100% tested and confirmed to work perfect

http://www.obdii365.com/wholesale/odis-4-13-software-for-vas-5054a.html

Free download+How to install: ODIS-S 4.3.3 Postsetup+Full Licence + Launcher

http://blog.obdii365.com/2018/02/26/odis-s-4-3-3-postsetup-full-licence-launcher/

https://eobd21.files.wordpress.com/2018/07/odis-4-3-3-install-image.jpg?w=150 150w, https://eobd21.files.wordpress.com/2018/07/odis-4-3-3-install-image.jpg?w=300 300w" sizes="(max-width: 439px) 100vw, 439px" />

ODIS 4.3 Release Notes:

Restrictions

Windows 10 only supports the new diagnostic interface VAS 6154 (known as the WLAN remote head). Users of the older models VAS 5054, VAS 5054A and VAS 5055 can continue to use the Windows 7 i.do client on existing systems until the End of 2019. The new diagnostic interface can be used with both operating systems. Please place any necessary orders with Workshop Equipment in good time

Functions in version 4.3

The key features newly added or revised in release 4.3 are

described briefly in this section and the additional CCB_DS IDs implemented are cited.

CCB 793

The ODIS system must allow the user to use cross-functional variables and passwords

declare.

CCB935

Conversion of Service42 interface to IA-compliant SOAP

CCB 942

Introduction of an attribute for unauthorized event memory, control of the GFS entry plan and GFS exit

CCB 1031

ASAM xml file customizations

CCB1548

Plagiarism check using VAS 5054A / 5055

CCB1623

VCI selection redesign

CCB 1653

complete test baseline and hotfix

CCB 2017

Extension of the action element “Logging”

CCB 2034

SFD activation OS (not yet available)

CCB2088

“Simulated Diagnostic Entry” in OD and GFS-Light

Defect resolution in version 4.3

The defects resolved in release 4.3 are described briefly in this section.

18907

FB_2016.16.00_015.33.0_With WLAN Funkopf 6154 ODIS hangs at the start module (read data)

19106

Department acceptance ODIS 4.0.0 B40 Separation from the vehicle not recognized

19126

SVM; KWP1281 Engine control unit flashing breaks off, flash process takes too long => timing

19361

ODIS S: Abort PDX Flashing over CAN

19387

Send Support Request: Bugatti Hotline Data will not be registered

19398

Error printing EGD protocol for non-legal VIN.

19405

OS error message “ODS4009E Internal” occurs, java.lang.NullPointerException

19413

When connecting to UDS controllers, Hex services are used instead of named ODX services

19561

GFS Light does not work

19565

OS 4.2.2 Error message during language change during a diagnostic session using a test baseline

19577

Change from “Flashing” to “Info” not possible because the button is grayed out

19589

Missing blank in notice message about not done update

Supported vehicles with Version 4.3

Approved AUDI vehicles

• All AUDI vehicles are supported

Approved Volkswagen vehicles

• All Volkswagen vehicles are supported

Approved Volkswagen Nutzfahrzeuge vehicles

• All Volkswagen Nutzfahrzeuge vehicles are supported

Approved Seat vehicles

• All Seat vehicles are supported

Approved Skoda vehicles

• All Skoda vehicles are supported

Approved Bentley vehicles

• All Bentley vehicles are supported

Approved Lamborghini vehicles

• The following Lamborghini vehicles are supported:

Gallardo from MY09-MY14 (only immobilizer and Radio PIN Code)

Aventador und Huracán

Approved Bugatti vehicles

• Bugatti Veyron and Bugatti Chiron are supported

Approved MAN vehicles

• MAN-TGE is supported

www.obdii365.com

http://blog.obdii365.com/2018/07/09/solved-vas5054a-odis-4-3-3-error-ods9004e/

Possible to read/write VAG ECU EDC17CP44 via OBD? And which tool can do it?

Here you go.

EDC17CP44 details:

Information:

ECU pins:

Pictures:

https://eobd21.files.wordpress.com/2018/07/edc17cp44_ecu-pin-1.jpg?w=150 150w, https://eobd21.files.wordpress.com/2018/07/edc17cp44_ecu-pin-1.jpg?w=300 300w" sizes="(max-width: 600px) 100vw, 600px" />

https://eobd21.files.wordpress.com/2018/07/edc17cp44_ecu-pin-2.jpg?w=150 150w, https://eobd21.files.wordpress.com/2018/07/edc17cp44_ecu-pin-2.jpg?w=300 300w" sizes="(max-width: 600px) 100vw, 600px" />

Vehicles with ECU EDC17CP44:

Kess V2 OBD writes edc17cp44: Success!

Car & ECU: EDC17CP44 Q7 / Touareg via OBD

Review: i have done edc17cp44 obd many times with kess

it is a virtual read need to have alientech databank access.

Btw, ktag readout also can be written with kess but have not tried it yet

Ktag reads edc17cp44: Success!

Car & ECU: Audi year 2011 edc17cp44

Review: I can read an Audi year 2011 edc17cp44 with ktag 6.070

FgTech eu clone reads edc17cp44: Success!

Car & ECU: VW Touareg 3.0tdi ecu edc17cp44

Review: I have been able to read it with fgtech euro clone in bootmode

MPPS cable OBD reads edc17cp44: Failed!

Car & ECU: Touareg II 4.2TDI edc17cp44

Review: I have done both ecu master and ecu slave boot read, than unlocked read files and flashed them back in boot mode.

When i do TPROT check it states that ecu is unlocked.

But when try OBD read, MPPS is reading ECU and when it comes to 100% i get message “This file is corrupt. Please make a boot read”

IMPORTANT:

it’s safer to do all boot mode

Please have full backups in case anything goes wrong.

Ktag/Kess Help File:

VAG BOSCH EDC17CP44 wiring https://eobd21.files.wordpress.com/2018/07/vag_edc_17cp44_kess-ktag-help-file-886x1024.jpg?w=130&h=150 130w, https://eobd21.files.wordpress.com/2018/07/vag_edc_17cp44_kess-ktag-help-file-886x1024.jpg?w=260&h=300 260w, https://eobd21.files.wordpress.com/2018/07/vag_edc_17cp44_kess-ktag-help-file-886x1024.jpg?w=768&h=888 768w, https://eobd21.files.wordpress.com/2018/07/vag_edc_17cp44_kess-ktag-help-file-886x1024.jpg 886w" sizes="(max-width: 640px) 100vw, 640px" />

www.obdii365.com

http://blog.obdii365.com/2018/07/06/read-vag-edc17cp44-kess-ktag-mpps-fgtech/