If there is no connection to the OBD connector with Xhorse VVDI Key Tool Plus, you can do a device test.

Follow instructions below to do a self-test.

Go to IMMO Programming- More functions- Device Test

Select K-line Test

Short connect PIN7 and PIN15 to do a K-line test.

You can also do a CAN-line test.

Then report the test result to us.

www.vvdishop.com

 Problem:

I have failed to update the Xhorse VVDI Mini OBD Tool firmware from 1.0.5 to 2.0.1. I have no luck in the App or via the Upgrade kit. Is there any solution?

Solution:

If failed to update mini obd tool firmware from 1.5.0 to V2.0.1, replace battery of mini obd tool.

Replace a new battery (CR2032), update firmware and sync device again.

 Can Xhorse Multi prog be used in offline mode like Vvdi prog?

You’re asking whether Multiprog can be used offline, similar to VVDI Prog.

Multiprog is a device programmer that typically requires a connection to a computer and the internet to function. However, there is an offline mode available for certain operations.

To use Multiprog offline, you’ll need:
1. _Multiprog software version 4.0 or later_: Ensure your software is up-to-date, as earlier versions might not support offline mode.
2. _Offline license_: You’ll need to obtain an offline license from the manufacturer or an authorized distributor. This license will enable offline mode.
3. _Pre-loaded data_: Before going offline, make sure you’ve pre-loaded the necessary data, such as device configurations and programming files.

In offline mode, you can perform certain operations, like:
– Reading and writing device configurations
– Programming certain devices
– Checking device information

 Problem:

It failed to do Xhorse multi prog firmware updates and now is says upgrading but nothing happens.

I tried reset button but same problem.

Software display error “Device Authentication Failed”. Any solution?

Solution:

Xhorse engineer suggests sync authorization to see if it is normal.

If you can sync authorization, try again. If not, restart the multi prog device and software.

User solutions:

1). Connect it to USB directly to the computer that has the program, turn off the equipment, turn it back on (with the USB already connected) and update the firmware, it works (it happened to me).

2). Something similar happened to me and i used another PC to do update via the LAN cable and it worked.

www.vvdishop.com

 How to read the Hyundai i10/i20 2014-2017 smart key module (SMK) using Xhorse Multi Prog programmer?

Select Hyundai i10/i20 Smart Key Module (2014-2017) and check wiring diagram.

Connect multi prog with smart key module following the wiring diagram.

Read ID ok

Read D-flash ok

Read P-flash in 2 min 4s successfully.

www.vvdishop.com

 What’s up guys! Today I’m gonna show how to add a smart key for 2019 Subaru Ascent with Xhorse VVDI Key Tool Plus by OBD. So let’s get started.

Immo programming >> Subaru >> Select from model >> Ascent >> 2019 >> With smart >> Start programming >> Key count

Key Tool Plus display the number of matched keys: 2

Add a key >> Yes

During matching, make sure all doors are in their current positions.

Keep a matched key close to start button…

Checking ID code, please wait…

Please place the keys to be matched close to the start button in turn within 60 seconds.

The number of matched keys=2

After all operations are completed, click OK to go to the next step.

Number of registered keys: 3

Please turn off the ignition.

Please turn on the ignition with each matched key in turn within 60 seconds.

Number of keys registered: 3

Note:

1. The key should be located in the car, near to the ignition switch button(ignitable area).
2. During matching, please ensure that all doors remain in their current positions.

Check two keys, both the original and the new one can work.

Perfect done.

www.vvdishop.com

 Xhorse Multi Prog user feedback: Kia Bosch MEG17.9.12 ECU Infineon TC1762 full clone successfully.

Select Kia Bosch MEG17.9.12 ECU.
Bench mode.
Read INT eeprom and INT flash.
Write INT eeprom and INT flash.

 Read Magneti Marelli 7GV CS and PIN with Xhorse VVDI Key Tool Plus successfully.

Menu path:
Immo Programming->VW-> Select by type-> Engine Control Unit-> Magneti Marelli 7GV

Read engine password

Key tool plus read PIN, CS and MAC successfully.

 Xhorse VVDI Key Tool Plus and Key Tool Max Pro released Renault and Daica Immobilizer software update on November 11th, 2024.

Xhorse is once again setting a new benchmark with a groundbreaking update to its IMMO database, specifically targeting RENAULT and DACIA vehicles. This vital update empowers automotive locksmiths to provide their customers with the most reliable, cutting-edge security solutions available today.

Before releasing this crucial update, Xhorse conducted extensive on-vehicle testing to ensure its reliability, safety, and efficiency, guaranteeing that the latest features meet the highest standards of performance.

Add following Renault and Dacia IMMO key programming models:

Renault

Smart Key

SCENIC 2016-
MEGANE 2015-
MEGANE SCENIC 2016-
QM6 (SAMSUNG QM6)
SM6 (SAMSUNG SM6)
TALISMAN 2015-
KADJAR 2016-
KOLEOS 2016-
ESPACE 2015-

Flip Key
MEGANE 2002-2008, 2008-2015, 2015-
SCENIC -2006, 2006-
MEGANE SCENIC 2002-2008, 2008-2015, 2015-
MODUS 2004-2012
CLIO 2006-2012
CLIO III
SM5 (SAMSUNG SM5) 2003-2004 2005-2009
SM6 (SAMSUNG SM6)
SM7 (SAMSUNG SM7) 2003-2004 2005-
QM6 (SAMSUNG QM6)
DUSTER 2014-2018, 2018-
KANGOO I
KANGOO II 2008-
KANGOO III 2020-
TRAFIC II Ph2
TWINGO I Ph3 2001-2006
SOLENZA
PRIMASTER
ESPACE 2015-
MASTER 2011-2016
KADJAR 2016-
TALISMAN 2015-
KOLEOS 2016-
SAFRANE 2009-
OROCH 2016-
ALASKAN 2016-
DOKKER LOGAN 2010-2013, 2013-
SANDERO 2013-2020
LODGY KWID (BRAZIL) 2023-2024
SYMBOL 2013-2018
TRIBBER 2014-2018
LAGUNA 2007-2011

Dacia
Flip Key
DOKKER
LODGY
DUSTER 2014-2018
SANDERO 2013-
LOGAN 2010-2013, 2013-

With the automotive industry increasingly shifting toward more sophisticated, secure technologies, the ability to stay ahead of these developments and seamlessly integrate them into your services will be a key differentiator for professional locksmiths.

This update is a prime example of Xhorse’s commitment to helping you remain at the forefront of the industry, ensuring that you can continue to offer top-tier security solutions to your customers.

https://www.vvdishop.com/info/xhorse-renault-dacia-immo-update-nov.-2024.html

 Another guide on reading VAG DQ200 transmission gearbox TCU using  Xhorse Multi Prog programmer and Godiag GT107+ DSG adapter.

To connect multi prog with GT107+ DSG adapter you also need a Godiag G-V ecu cable converter like this.

Here is the overall connection diagram.

Connect multi prog with Godiag G-V ECU cable and GT107+ DSG gearbox adapter

Connect GT107+ jumper cable with DQ200 TCU

Connect multi prog with PC via USB cable and power adapter, turn on multi-prog programmer.

Run Multi prog software, quick search DQ200 gearbox

Connects with TCM. Read INT eeprom.

Connects with gearbox, you can see voltage and current on the GT107+ adapter.

Read and save INT eeprom.

Then read and save INT flash.