Xhorseキープログラミングツール

 We are going to clone a computer from a Chevrolet Express 4.3 engine V6. This is an ACDelco E37 ECM. We are going to do it with Xhorse multi prog on the platform (bench mode) without opening the computer.

Select GM E37->Chevrolet->Express 1500, we see the ID, the type of unit that is a Chevrolet Express 1500.

Check wiring diagram in multiprog.

We going to place the PINs we have two red ones that are 12V of power supply, we have CAN H and CAN L and GND.

It is very simple to make this connection.

Read EXT eeprom
Read eeprom data successfully in 2min 24s.

Save eeprom data.

Read EXT flash.

Save flash data.

Connect donor ECM with xhorse multi-prog follow the same wiring diagram.

Backup donor ECM eeprom and flash.
Then write original eeprom to donor ECM.

Write original flash data to donor ECM.
Verify checksum.
Checksum calculation successful.

Write flash takes longer, 9min 14s.

Clone E37 ECM successfully.

Install donor ECM to vehicle.

Car starts fine. It works perfectly.

www.vvdishop.com

 This is a Jeep control board with M95320 eeprom chip. We will show how to read this chip using Xhorse Multi Prog without laptop and PC software.

Connect M95320 EEPROM IC chip and Multiprog via a goog 8-pin clip adapter.

In multi prog, select Chip operation->M95XXX->M95320->Status

Read chip.

Read eeprom successfully. Then save data.

You can see file in Files folder.

You can save it to local to this or you can share it with you are connected to a Wi-Fi.

 Problem:

Trying to do an Xhorse vvdi key tool plus DB15 self-test but failed. Any advice?

Solution:

When doing DB15 self test, don’t connect any cables/adapters.

If still the same error, there is something wrong with the device. You may need to send back for repair.

 How to find the key for 2023 Toyota Corolla Push with vvdi key tool max and XM38 Toyota?

Here is the clue.

Successfully generated Xhorse XM38 key with key tool max.

Use the Corolla 2561/1320 ID4A FCC ID HYQ14FBW option.

It works to lock and unlock the car, we modify the frequencies.

Trunk should be 09
Panic 10
Lock 01
Unlock 02

Frequencies should be like that. This is a perfect key. The key works just flawlessly. It starts the car.
If you guys ever need a 2023 Toyota Corolla this is how you’re going to generate that.

www.vvdishop.com

 Xhorse VVDI Key Tool Plus program Seat Ateca 2019 MQB RH850 locked key successfully.

It’s Seat Ateca 2019 with digital dash, with RH850 wire bond. Processor R7F701401.

Read and obtain immo data, make dealer key (using Autel IKey), and learn key via key tool plus and RH850 adapter. Keyless entry and keyless lock work with no problem.

 Xhorse Multi Prog read and write Hyundai KEFICO MEG17.9.13 ECU on bench successfully.

Select Hyundai->Kia MEG17.9.13

Check wiring diagram

Connect Multi-prog with ECU following the pinout.

Read INT eeprom

Read INT flash

Back up data successfully.

We are going to do IMMO OFF.

Upload the modified IMMO OFF file and write flash.

Multi prog will ask you to do a checksum correction.

Checksum calculation successfully.

Write flash until finished.

www.vvdishop.com

 Xhorse VVDI MB Tool and VVDI Key Tool Plus use different MB power adapter for Benz password fast online calculation.

These power adapters cannot be mixed used, otherwise, you will get “MB Power Adapter Response Error”.

They can be identified by their appearance.

This is the MB power adapter for VVDI MB. It has 1 hole on 1 side only.

This is the MB power adapter for Key tool plus. It has 1 hole on both sides.

 Problem:

A customer was trying to read Benz EZS password with MB power adapter for fast reading, but vvdi key tool plus reported an error “MB power adapter response error”.

Image attached:

Solution:

Go to Immo programming-Benz-Select from system-Special function-Detect mb power adapter-Turn on the power adapter, then try again.

www.vvdishop.com

 How-to: read Porsche MLB Key Immo Data by Xhorse VVDI MLB Tool Key programmer.

Place the key in the device identification area and click OK for identification.

Read key ID and info. The key is locked.

Remove key shell and take out PCB.

Check wiring diagram. Need to remove capacitors.

Then solder wires to the key board.

Place the key in the VVDI MLB Tool identification area and click OK for identification again.

Select Collect key data.

Choose Collect original keys- points deduction. The calculation will deduct 200 points.

Online calculate immo data completed.

Save data.

Now you can make dealer key and learn MLB key.

www.vvdishop.com

 Problem:

Xhorse VVDI2 does not detect super chip XT27, but my colleague’s device is exctaly the same device, it see them, and all operations with it are reset and assigned a different value.

The device does not work only with super chips, all other chips work.

Error: ‘Not detect VVDI Super Chip‘

Solution:

Go to Options tab->Set Parameters.

Set antenna gain value to 0,1, 2, 3 respectively and try again.

If all failed to detect super chip, there is something wrong with your vvdi2. Need to send back your seller for repair.

www.vvdishop.com