Both Xhorse VVDI2 and VVDI BIMTool pro software support BMW BDC unlock via OBD, today I’m gonna try it with VVDI BIMTool Pro Tool. By firstly unlocking and programming BDC module, then make a dealer key. The whole process is on the car without removing any modules.

Step1. Unlock & Program BDC

After connection, open VVDI BMW Tool software:

Click “Programming FEM/BDC system”.

Attention: support unlock BDC via OBD directly, no need on the bench, no need read/write EEPROM.

Press YES to start unlock via OBDII(require internet support).

Press NO to start with special EEPROM method.

Click “Yes”.

Reading coding…

Save BDC code file.

Please record the module information, next will perform module programming! It requires about 10 minutes, please make sure the car voltage above 13V.(1)

Click “OK”.

Updating system… please wait until 100%

FEM/BDC update success. Please check the car and key status!

You can perform key learning function if car work as normal!

Step 2. Make a Dealer Key

Select a blank key position: Key6>> Prepare dealer key with ignition switch>> Known ISN >> NEXT

Please record the following information includes:

FEM/BDC security key

DME/CAS security key

Key/CAS security key

ECU ISN

Please input a new key into ignition coil.

Learning key, please wait finish…

Key learn success.

Now we can read out Key6 information.

Test the new key, everything works perfectly.

So we can successfully use VVDI BIM Tool to unlock BMW BDC by OBD.

https://www.vvdishop.com/service/unlock-bmw-bdc-with-vvdi-bim-tool-by-obd.html

 Xhorse VVDI2 V7.3.5 software update BMW BDC unlock via OBD.

Report today:

BMW X1 12/2019  BDC SWFL unlock success via OBD with VVDI2 and key programmed fast and easy.
VVDI tools using a lot and never was failed, at least damaged something!
In this type of job you need to be ready for some background solution if something going wrong, if you not ready need going away from this field!
VVDI tools very good tool for that money.

NOTE:

SWFL_00002419.085.xxx.xxx version cannot be unlocked by OBD.

 Does the Xhorse dolphin xp005l (dolphin ii) key cutting machine have a key counter to see how many keys have been cut?

Yes, it does. In Dolphin II app you will see how many keys have been cut (marked red below)

 Question: I need to program a universal Xhorse key for European Opel Vectra C 2005, original key ID 46 as in the photo. There is no vectra C in the vvdi mini key tool selection.

If generate remote under this option, remote not work after programming with im608.

Solution:

Some managed to generate remote under this key option: PCF7946 Delphi BSI

Review:

2005 Opel Vectra C Fiat Delphi BSI software was applied to the xhorse super XE remote, the pin code was received by autel, the coding was done with xtool x100 pad3.
Note: The communication with the vehicle computer could not be established for a long time, the car was left running for 15 minutes, then the coding was successful.

If you fail to use this option, use aftermarket Pcf7946 or original key. Then program with key programmers T300, CK100 etc.

www.vvdishop.com

 Xhorse VVDI PROG is able to reset Hyundai i20 Elite 96910-C7000 airbag by reading/writing DFLASH & CFLASH data on Bench. Easy jobs in minutes, next we’re gonna to show the steps.

Open VVDI PROG software to select model:

Type: 2-MCU

Brand: ST-SPC560XXXX

Chip: SPC560P50L3

Follow the connection diagram to connect VVDI PROG& airbag module by MCU Reflash Cable. Need to solder VCC, GND, RESET, TD0, TCK, TMS, TDI pins.

After successful connection, we can start reading.

DFLASH >> Read

Read success.

CFLASH >> Read

Reading…(100%)

Read success.

Now we can continue to perform writing as needed.

www.vvdishop.com